Seattle Washington Building Expert Directory

Homebuilder Confidence Takes a Beating

October 21, 2013 — CDJ STAFF
Homebuilder confidence dropped to fifty-five percent in October, the lowest percentage seen in the last four months. The score had been rising on the strength of renewed home sales. The current slump is attributed to increases in interest rates, which have made home purchases more expensive for prospective buyers, and the uncertainty of the budget struggle in Washington. John Stumpf, the chairman and CEO of Wells Fargo said that “home price appreciation remains strong and affordability remains excellent.” Mr. Strum has “guarded optimism” over the effects of the budget struggle. Read the court decision
Read the full story...
Reprinted courtesy of

The Basics of Subcontractor Defaults – Key Considerations

February 15, 2021 — Gerard J. Onorata - Peckar & Abramson, P.C.
The success of general contractors in completing a construction project is often dependent upon the performance of their subcontractors. General contractors have frequently said exactly this. Traditionally, the key subcontractors on a project are the electrical, plumbing, HVAC and structural steel subs. Due to the fundamental nature of the work performed by these trades, the risk of defaulting and terminating one or more of them is likely to have a substantial impact on the project, more so than with the trade contractors that perform their work after a building is made weather tight (i.e., drywall, tile, painting). Most general contractors have, over a period of years, established longstanding relationships with certain subcontractors that they have come to depend upon. The risk of having to default and terminate one of these subs is minimal. Nevertheless, there will inevitably arise occasions when even a once reliable subcontractor fails to perform and it becomes necessary to invoke the remedies of default and termination. Areas ripe for controversy with subcontractors that often can lead to default and termination often involve disputes over change orders and the scope of work, the installation of defective work and the back-charges that ensue therefrom, and, to a lesser extent, conflicts that arise from ambiguous plans and specifications and the extra work and delays caused by the discovery of unforeseen site conditions. Read the court decision
Read the full story...
Reprinted courtesy of Gerard J. Onorata, Peckar & Abramson, P.C.
Mr. Onorata may be contacted at gonorata@pecklaw.com

Home Prices Up, Inventory Down

February 04, 2013 — CDJ STAFF
"Housing is clearly recovering," David Blitzer of Standard & Poor told USA Today. Standard & Poor issued their Case-Shiller Index of home sale prices for November. In their review of twenty metropolitan areas, prices rose in all but one area. In the report for October, housing overall saw a 0.1% decline with gains only in ten cities. The article attributes this in part to that the inventory of unsold homes was 4.4 months, which was the lowest since May 2005. "Any new listings are getting eaten up right away," said E. J. Bowlds, a broker at Coldwell Banker Bain. He is seeing six to ten competing offers on homes in his area of Washington State. Read the court decision
Read the full story...
Reprinted courtesy of

Are Proprietary Specifications Illegal?

April 11, 2018 — Wally Zimolong – Supplemental Conditions
A friend came to me with a question regarding a case he was working: “can a public owner require that bidders use a specific brand name product?” “Of course not,” I said “proprietary specifications are illegal.” Or, at least that’s what I assumed. To my surprise, the law in the Commonwealth of Pennsylvania is not as clear as it is in other jurisdictions. What is a proprietary specification? A proprietary specification lists a product by brand name, make, model and/model that a contractor must (shall) utilize in construction. A basic example of a proprietary specification would state:

“Air Handlers shall be “Turbo Max” as manufactured by Chiller Corp.”

There are two problems with a proprietary specification (other than potentially being illegal): (a) they limit competition, and (b) invite steered contract awards. They limit competition because it limits the type of material that can be used on the project. In the example above, there could be equivalent air handlers available at a better price but the contractor could not use that lower priced product in its bid. Thus, the taxpayers end up paying more for tile. Also, contractors may not be able to secure a certain brand name product because of exclusive distribution agreements. Again, using the example above, contractor A’s competitor may have the exclusive distribution agreement with Chiller Corp. Read the court decision
Read the full story...
Reprinted courtesy of Wally Zimolong, Zimolong LLC
Mr. Zimolong may be contacted at wally@zimolonglaw.com

BIM Legal Liabilities: Not That Different

February 10, 2020 — Christopher G. Hill - Construction Law Musings
For this week’s Guest Post Friday here at Musings, we welcome Scott P. Fitzsimmons. Scott is an attorney with the construction law firm Watt, Tieder, Hoffar & Fitzgerald, where he represents contractors, subcontractors, owners, and engineers. He is also a LEED AP and an instructor for AGC of D.C., where he teaches BIM Contract Negotiation and Risk Allocation as part of AGC’s Certificate of Management, Building Information Modeling program. When a new technology is introduced to the construction industry, contractors inevitably ask themselves one question “Great, how can this new gadget get me into trouble?” Building Information Modeling (BIM) is exactly the kind of technology that raises this fear. But, BIM has been around for a few years now, and the construction industry has done a good job of curtailing the fear of unanticipated legal liability. Nevertheless, contractors should be aware of the pitfalls BIM introduces and should know how to limit their risk arising from this new “gadget.” Often described as “CAD on Steroids,” BIM is truly much more than a simple design program. Along with early clash detection, BIM provides time and cost integration; calculates energy efficiency; and assists building maintenance long after project completion. Unlike CAD, BIM also modifies the collaborative nature of a construction project. Thus, subcontractors no longer review a design, submit shop drawings, and go to work. Rather, subcontractors are brought into the design process early in the project and often are asked to contribute to the design long before construction begins. Asking a contractor or subcontractor to provide design services appears to shift the roles of an architect and a contractor. So, the questions abound: Is a contractor now responsible for design? Can the contractor be held responsible for defective design? Do not fret. To date, there has been only one advertised case addressing BIM liability. The reason is simple. For almost a hundred years, the United States Supreme Court has held that contractors are not responsible for defective design on a traditional design-bid-build project. Using BIM, therefore, should not modify a contractor’s responsibility. But, to ensure that your obligations do not extend beyond construction, all BIM requirements should be in writing and made part of your contract. Read the court decision
Read the full story...
Reprinted courtesy of The Law Office of Christopher G. Hill
Mr. Hill may be contacted at chrisghill@constructionlawva.com

Cal/OSHA ETS: Newest Version Effective Today

January 17, 2022 — Amy R. Patton, Matthew C. Lewis & Rana Ayazi - Payne & Fears
The newest version of the Cal/OSHA ETS goes into effect today, Jan. 14, 2022, and will expire on April 15, 2022. A redline of the recently expired Cal/OSHA ETS and the newest Cal/OSHA ETS is available HERE. The newest Cal/OSHA ETS, which was drafted prior to Dec. 16, 2021, is already partially out-of-date based on the California Department of Public Heath’s Guidance For the Use of Masks (released Jan. 5, 2022) and the CDPH’s Guidance for Local Health Jurisdictions on Isolation and Quarantine of the General Public (released Jan. 8, 2022); these changes have been addressed in the Cal/OSHA ETS FAQs. With all of these changes occurring (not to mention all of the litigation surrounding the now-stayed federal OSHA ETS), California employers are asking: How do I comply with the current Cal/OSHA ETS and the updated CDPH Guidance? Here are the key points to ensure you are in compliance:

New Shorter Isolation and Quarantine Periods

Day 0: First day of symptoms or the day a positive test specimen was collected. Begin isolation.
Day 1: First full day after symptoms developed or positive test specimen was collected.
Day 5: Recommended day to take COVID-19 test.

Reprinted courtesy of Amy R. Patton, Payne & Fears, Matthew C. Lewis, Payne & Fears and Rana Ayazi, Payne & Fears Ms. Patton may be contacted at arp@paynefears.com Mr. Lewis may be contacted at mcl@paynefears.com Ms. Ayazi may be contacted at ra@paynefears.com Read the court decision
Read the full story...
Reprinted courtesy of

Cal/OSHA’s Toolbox Has Significantly Expanded: A Look At Senate Bill 606

December 13, 2021 — Michael J. Studenka - Newmeyer Dillion
Governor Gavin Newsom recently signed into law Senate Bill 606, set to take effect on January 1, 2022. With proponents of the bill citing the need to hold large employers accountable for COVID-related workplace hazards, SB 606 creates two new categories of employer violations. First, SB 606 creates a rebuttable presumption that if a type of violation is discovered at one particular worksite, Cal/OSHA can extrapolate that the violation is an “enterprise-wide” violation at all of the other company worksites. Additionally, SB 606 adds a new category of “egregious violations” to Cal/OSHA’s arsenal, adding a penalty multiplier for such violations. Finally, SB 606 increases Cal/OSHA’s investigative capabilities by authorizing Cal/OSHA to issue a subpoena to employers should they fail to “promptly provide” information requested during an investigation. As further explained below, the consequences of violating Cal/OSHA regulations has become significantly greater and more expensive, particularly for larger employers with multiple worksites. ENTERPRISE-WIDE VIOLATIONS AND THE SEVERE REMEDIES THAT FOLLOW Under SB 606, employers with more than one worksite will now face a rebuttable presumption that a violation at one location is actually “enterprise-wide” if either of the following are true:

A written policy or procedure violates any Cal/OSHA standard, rule, order or regulation; OR
Cal/OSHA finds evidence of a “pattern or practice” of the same violation being committed by the employer at one or more of its worksites.

Read the court decision
Read the full story...
Reprinted courtesy of Michael J. Studenka, Newmeyer Dillion
Mr. Studenka may be contacted at michael.studenka@ndlf.com

Pre-Suit Settlement Offers and Construction Lien Actions

July 21, 2018 — David Adelstein - Florida Construction Legal Updates
It is unfortunate, but in certain matters, a construction lien foreclosure action is not actually driven by the principal amount in dispute. Oh no. Rather, it is driven by attorney’s fees. That’s right. Attorney’s fees. This is true even though Florida applies the significant issues test to determine the prevailing party for purposes of attorney’s fees. However, oftentimes the prospect of attorney’s fees is enough for parties to fear that exposure. There is a 1985 Florida Supreme Court case that I like to cite if applicable, C.U. Associates, Inc. v. R.B. Grove, Inc., 472 So.2d 1177, 1179 (Fla. 1985), that finds, “in order to be a prevailing party entitled to the award of attorney’s fees pursuant to section 713.29 [a construction lien claim], a litigant must have recovered an amount exceeding that which was earlier offered in settlement of the claim.” Accord Sullivan v. Galske, 917 So.2d 412 (Fla. 2d DCA 2006) (explaining that although contractor is receiving a judgment in his favor, he may not be the prevailing party if the homeowner offered to settle prior to the lawsuit for an amount equal to or greater than the award in the judgment). Read the court decision
Read the full story...
Reprinted courtesy of David Adelstein, Kirwin Norris
Mr. Adelstein may be contacted at dma@kirwinnorris.com

SEATTLE WASHINGTON BUILDING EXPERT DIRECTORY AND CAPABILITIES