Contrasting Expert Opinions Result in Denial of Cross Motions for Summary Judgment
February 27, 2023 —
Tred R. Eyerly - Insurance Law HawaiiGiven the opposing experts' contradictory reports, the court denied both the insured and insurer's motions for summary judgment regarding coverage for a pipe leak. Pronti v. Hanover Ins. Co., 2022 U.S. Dist. LEXIS 222306 (W.D. N. Y. Dec. 9, 2022).
The insured had a swimming poll and spa, which functioned using a subsurface plumbing system, covered with concrete decking. A subsurface pipe began to leak, preventing the pool from properly functioning. The insureds gave notice under their homeowners' policy and contended that significant portions of the pool, spa, concrete decking and other landscaping had to be torn out to do repairs. The insurer retained an expert, Sarah G. Byer, a structural engineer, to investigate. The parties agreed that the pipe had a leak, but disputed if the location of the leak was specifically identified.
The parties also disputed the cause of the leak. Byer found that the most likely cause was deterioration incurred over the pipe's lifetime based on the age of the plumbing system and Byer's personal observation of the pipe. Byer further stated that the physical qualities of flexible PVC piping made it susceptible to damage from chlorine and water over time.
Read the court decisionRead the full story...Reprinted courtesy of
Tred R. Eyerly, Damon Key Leong Kupchak HastertMr. Eyerly may be contacted at
te@hawaiilawyer.com
California Supreme Court Adopts “Vertical Exhaustion” in the Long-Storied Montrose Environmental Coverage Litigation
June 08, 2020 —
Gregory S. Capps & Michael E. DiFebbo - White and Williams LLPOn April 6, 2020, the California Supreme Court issued a decision that held a policyholder is entitled to access available excess coverage under any excess policy once it has exhausted directly underlying excess policies for the same policy period in Montrose Chemical Corporation v. the Superior Court of Los Angeles County, Supreme Court of California, case number S244737. In its unanimous decision adopting this “vertical exhaustion” requirement, the court rejected the “horizontal exhaustion” rule urged by the policyholder’s excess insurers, under which the policyholder would have been able to access an excess policy only after it had exhausted other policies with lower attachment points from every policy period in which the environmental damage resulting in liability occurred.
In 1990, Montrose sought coverage under primary policies and multiple layers of excess policies issued for periods from 1961 through 1985 for environmental damage liabilities arising from its production of insecticide in the Los Angeles area between 1947 and 1982. The ongoing dispute currently arises out of Montrose’s Fifth Amended Complaint which was filed in 2015 seeking declarations concerning exhaustion and the manner in which Montrose may allocate its liabilities across the policies. Each of the excess policies at issue contained a requirement of exhaustion of underlying coverage. The various policies described the applicable underlying coverage in four main ways: (1) some policies contained a schedule of underlying insurance listing all of the underlying policies in the same policy period by insurer name, policy number, and dollar amount; (2) some policies referenced a specific dollar amount of underlying insurance in the same policy period and a schedule of underlying insurance on file with the insurer; (3) some policies referenced a specific dollar amount of underlying insurance in the same policy period and identified one or more of the underlying insurers; and (4) some policies referenced a specific dollar amount of underlying insurance that corresponds with the combined limits of the underlying policies in that policy period. The excess policies also provided, in various ways, that “other insurance” must be exhausted before the excess policy can be accessed.
Reprinted courtesy of
Gregory S. Capps, White and Williams LLP and
Michael E. DiFebbo, White and Williams LLP
Mr. Capps may be contacted at cappsg@whiteandwilliams.com
Mr. DiFebbo may be contacted at difebbom@whiteandwilliams.com
Read the court decisionRead the full story...Reprinted courtesy of
What if the "Your Work" Exclusion is Inapplicable? ISO Classification and Construction Defect Claims.
February 14, 2023 —
David Humphreys - Carson Law Group, PLLCThis article was first published by the National Association of Home Builders (NAHB) on their NAHBNow blog
One of the risks faced by a residential builder is that, following completion of construction, the homeowner may assert a claim against the builder for damage to the home caused by an alleged construction defect. One of the ways a builder manages the risk of such construction defect claims is by purchasing commercial general liability (“CGL”) insurance.
A builder’s CGL policy covers those sums the builder is legally obligated to pay as damages because of bodily injury or property damage caused by an “occurrence,” that is, damage that is accidental rather than being expected or intended by the builder, so long as the claim does not fall within any of the policy’s several “exclusions” from coverage.
When faced with a construction defect lawsuit, our builder clients are often surprised—and dismayed—when their CGL insurer denies coverage and refuses to defend the builder. However, builders shouldn’t take their insurer’s denial of coverage at face value. This article discusses a new argument we recently discovered that has been a game-changer for our builder clients who were denied coverage in construction defect cases.
Whether coverage exists always depends on the specific language of the particular CGL policy, and courts generally construe exclusions against insurers. This allows experienced coverage attorneys to, at times, successfully challenge declinations of coverage and, at a minimum, convince insurers to pay for the builder’s defense.
A typical CGL policy provides products-completed operations coverage, which is sought by businesses that face potential liability arising out of the products that they have sold or operations that they have completed. Products-completed operations coverage allows builders to obtain many years of coverage for a completed project. Over the years, insurers have added to their policies modifications and exclusions that limit their exposure for claims that fall under that coverage.
Exclusion (l) or the “your work” exclusion, will often exclude coverage for a latent defect claim against the builder. A standard “your work” exclusion provides:
This insurance does not apply to: . . . “[p]roperty damage” to “your work” arising out of it or any part of it and included in the “products-completed operations hazard.”
This “your work” and similar exclusions are designed to limit coverage for business risks that are within the contractor’s own control; e.g., a claim that the contractor caused damage to the contractor’s own work. These exclusions apply both to ongoing and completed projects, which can leave a builder unprotected from lawsuits for years after a project is completed.
However, builders who are classified on the declarations page with Code 91580 Contractors— Executive Supervisors or Executive Superintendents, may not be subject to the “your work” exclusion. 91580 is a common classification assigned to builders during insurance underwriting. This classification falls into what is referred to as “dagger class” or “plus sign class,” which indicates that Products and/or Completed Operations coverage is
included as part of and not separate from the Premises/Operations coverage (emphasis added).
It has been noted that dagger” and “plus sign” classifications create confusion because of the seeming contradiction between policy wording and coverage rules.* The CGL policy seems to expressly exclude products and/or completed operations losses for “dagger” or “plus sign” classes. In the definitions section we find the following:
“Products-completed operations hazard”: . . .b. Does not Include “bodily Injury” or “property damage” arising out of:. . . (3) Products or operations for which the classification, listed In the Declarations or in a policy schedule, states that products- completed operations are subject to the General Aggregate Limit.”
This apparent exclusionary language, however, must be read in conjunction with the Insurance Services Office’s (ISO) Rule 25.F.1.:
Rule 25. CLASSIFICATIONS
F. Symbols
1. Plus Sign
A plus sign when shown in the Premium Base column under General Liability insurance in the Classification Table - means that coverage for Products and/or Completed Operations is included in the Premises/Operations coverage at no additional premium charge. When this situation applies, the classification described in the policy schedule or Declarations must state that:
“Products-completed operations are subject to the General Aggregate Limit” to provide Products and/or Completed Operations coverage(s).
When read together then, the exclusionary wording in the policy definition removes any product or operation loss subject to the “dagger” or “plus sign” classification from the definition of Products Completed Operations Hazard. Under the dagger or plus sign classification of Rule 25, coverage for products and/or operations is included in the premises operations coverage. Consequently, a loss can no longer be defined as a product completed loss, and as a result it is no longer subject to the “your work” exclusion.
Recall that the standard “your work” exclusion quoted above excludes coverage for “property damage” to “your work” “arising out of it or any part of it
and included in the “products-completed operations hazard”.” Here, we emphasize “and” because the “your work” exclusion applies only to property damage that is also included in the “products-completed operations hazard.” Since property damage claims arising under “plus sign” classifications are expressly excluded from the “products-completed operations hazard” (they are included in the premises/operations coverage) the “your work” exclusion simply does not apply. This means that, if your CGL insurer denies your construction defect claim based on the “your work” exclusion, do what the title of this article suggests: Check your ISO classification! If 91580 “Executive Supervisors or Executive Superintendents” is listed on your Declarations page, you may be in luck.
This new ISO classification-based coverage argument will likely also apply to other exclusions and endorsements that CGL insurers routinely rely on in denying coverage in construction defect cases. We recently successfully challenged a coverage denial based on the following “prior work” exclusionary endorsement:
”This insurance does not apply to ‘your products’ or ‘your work’ completed prior to” a certain date listed in the endorsement. . .
“Specifically, this insurance does not apply to. . . “property damage”. . . included in the ‘products-completed operations hazard’ and arising out of. . . ‘your work’ performed by or on behalf of you prior to the date shown above.”
Again, this endorsement incorporates the “products-completed operations hazard,” which allowed us to successfully argue that the exclusion was inapplicable to a builder classified as a 91580 “Executive Supervisor or Executive Superintendent.”
To our knowledge, this new ISO classification-based coverage argument has not yet been addressed by a court. Our recent successes with it have concluded with favorable settlements for our clients. Accordingly, for now, the ISO classification-based argument is a powerful new tool to challenge denials of coverage in construction defect cases where the builder is classified under 91580 “Executive Supervisors or Executive Superintendents.”
David Humphreys is a Partner at Carson Law Group, PLLC, and has been representing construction contractors, subcontractors, and owners for more than two decades in Mississippi and throughout the Southeast.
*See “Dagger” or Plus Symbol Classes: What They Mean, Chris Boggs - Virtual University | “Dagger” or Plus Symbol Classes: What They Mean) (independentagent.com)
Read the court decisionRead the full story...Reprinted courtesy of
The Unwavering Un-waivable Implied Warranty of Workmanship and Habitability in Arizona
January 23, 2023 —
Robert A. Henry & Emily R. Parker - Snell & Wilmer Real Estate Litigation BlogThe Arizona Supreme Court recently issued an opinion on the scope of the implied warranty of workmanship and habitability (the “implied warranty”) in contracts between homebuyers and builder/vendors that provides clear guidance of the law in this area, specifically on the issue of whether the implied warranty can be waived or disclaimed. It is also an interesting and helpful read for those who engage in new home residential sales and real estate transactions generally.
The case:
Zambrano v. M & RC, II LLC, 254 Ariz. 53 (2022). The takeaway holding: the implied warranty of workmanship and habitability cannot, under any circumstances, be disclaimed or waived.
From a practice perspective, the foregoing is likely all one needs to ultimately know. However, the majority opinion (authored by Justice Timmer) and the dissent (authored by Justice King, and joined by Justice Bolick) are in these authors’ opinions worth a read for those who want a better understanding of the contours of how “public policy” plays into the analysis of the enforceability of contract terms, especially in the real estate context and even more particularly in connection with contracts for the sale of new homes. The careful analysis of both the majority opinion and the dissent provides an excellent history of the implied warranty, the public policy behind it, and its scope and application in the context of competing public policies, most notably the freedom to contract.
Reprinted courtesy of
Robert A. Henry, Snell & Wilmer and
Emily R. Parker, Snell & Wilmer
Mr. Henry may be contacted at bhenry@swlaw.com
Ms. Parker may be contacted at eparker@swlaw.com
Read the court decisionRead the full story...Reprinted courtesy of
Why Insurers and Their Attorneys Need to Pay Close Attention to Their Discovery Burden in Washington
March 28, 2018 —
Neal Philip – Insurance Law BlogAs previously reported in this blog, Washington case law generally affords insureds a broad right to the discovery of claim file materials, including information that should be protected from disclosure by attorney/client privilege or the work product doctrine.
Cedell v. Farmers Ins. Co. of Washington, 176 Wn.2d 686, 295 P. 3d 239 (2013). The discovery pitfalls created by
Cedell were on full display in a recent Western District of Washington decision that granted an insured’s motion to compel production of work product and attorney/client communications from an insurer’s claims file.
Westridge Townhomes Owners Ass’n v. Great American Assur. Co., 2018 U.S. Dist. LEXIS 27960 (W.D. Wash. February 21, 2018)
The background facts are somewhat unclear, but it appears that the insured in this case made a claim for coverage under two insurance policies and there was an allegedly inadequate response from the insurers. The insured sued its insurers for coverage in 2016 before the insurers issued a declination of coverage letter. The two insurers retained the same attorney to represent them, and that attorney subsequently wrote a declination letter on behalf of the insurers, which was sent to the insured on April 12, 2017. The insured ultimately sought production of the entire claim file, which had not been split between the claim investigation and the coverage litigation. The insurers argued, among other things, that the insured was not entitled to anything after the litigation commenced in 2016 on work product grounds, and certainly was not entitled to communications with their attorney.
Read the court decisionRead the full story...Reprinted courtesy of
Neal Philip, Gordon, Reese, Scully, & MansukhaniMr. Philip may be contacted at
nphilip@grsm.com
Subcontractors Eye 2022 with Guarded Optimism
October 11, 2021 —
Louise Poirier - Engineering News-RecordWhile work continues to be plentiful for specialty contractors across the five-state region of Arkansas, Louisiana, Mississippi, Oklahoma and Texas, concerns remain for how the project landscape will continue to evolve as the impacts of the COVID-19 pandemic continue to weigh on the world.
Reprinted courtesy of
Louise Poirier, Engineering News-Record
Ms. Poirier may be contacted at poirierl@enr.com
Read the full story... Read the court decisionRead the full story...Reprinted courtesy of
Largest US Dam Removal Stirs Debate Over Coveted West Water
May 11, 2020 —
Associated Press - Engineering News-RecordKLAMATH, Calif. (AP) — The second-largest river in California has sustained Native American tribes with plentiful salmon for millennia, provided upstream farmers with irrigation water for generations and served as a haven for retirees who built dream homes along its banks.
With so many competing demands, the Klamath River has come to symbolize a larger struggle over the increasingly precious water resources of the U.S. West, and who has the biggest claim to them.
Engineering News-Record
ENR may be contacted at ENR.com@bnpmedia.com
Read the full story... Read the court decisionRead the full story...Reprinted courtesy of
SunCal Buys Oak Knoll Development for the Second Time
May 19, 2014 —
Beverley BevenFlorez-CDJ STAFFAccording to the San Francisco Business Times, “Irvine-based SunCal has now bought the same site twice: once in 2005 for $100.5 million and again last week from the Lehman Brothers estate.” Suncal’s original plan to develop the 167-acre Oakland Hills, California project “fell apart after Lehman declared bankruptcy in 2008.”
The San Francisco Business Times reported that the “former naval hospital site” has “the potential for more than 900 homes.” The former design included “960 homes, 82,000 square feet of commercial and retail space, and 50 acres of parks and open space.”
Read the court decisionRead the full story...Reprinted courtesy of
